BIS Certification for Aluminum Alloy Welded Tubes for Irrigation Purposes IS 7092 Part 1
Category: BIS Certification
Introduction to Indian Standard IS 7092 Part 1 covers Aluminium Alloy Welded Tubes for Irrigation Purposes. This standard specifies the manufacturing, chemical and physical requirements and testing of aluminium alloy Welded Tubes for Irrigation Purposes.
The tubes shall be manufactured from raw material strips/sheets conforming to the aluminium alloys 31000, 31500, 40800, 51300, 52000, 53000 and 55000 as per IS 737.
What Are Aluminium Alloy Welded Tubes for Irrigation Purposes?
If you manufacture or import Aluminium Alloy Welded Tubes for Irrigation Purposes in India, obtaining BIS certification under IS 7092 Part 1 is a legal requirement not an option. The Bureau of Indian Standards (BIS) mandates the ISI Mark on these products under the Quality Control Order issued by the Ministry of Commerce and Industry, Department for Promotion of Industry and Internal Trade. Unlike extruded tubes, welded aluminium irrigation tubes are manufactured from raw material strips and sheets conforming to aluminium alloys 31000, 31500, 40800, 51300, 52000, 53000, and 55000 as specified under IS 737.
The seam-welded construction makes these tubes lightweight, corrosion-resistant, and cost-effective for large-scale irrigation infrastructure across India. Non-compliance with the ISI Mark requirement can result in product seizure, significant financial penalties, and loss of market access.
IS 7092 Part 1 of Quality Parameters Specified
IS 7092 Part 1 governs the following quality characteristics for Aluminium Alloy Welded Tubes for Irrigation Purposes:
- Chemical Composition: Alloy-wise elemental requirements per IS 737
- Dimensions and Tolerances: Permissible size variations for each nominal size
- Flattening Test: Verifies structural integrity of the weld seam under pressure
- Hydrostatic Pressure Test: Confirms leak-proof performance under operating conditions
- Tensile Properties: Minimum strength requirements for safe field use
Mandate for ISI Mark Certification (IS 7092 Part 1)
Under Section 14 of the Bureau of Indian Standards Act, 1986, the Ministry of Commerce and Industry — in consultation with BIS — has issued a mandatory Quality Control Order for Aluminium Alloy Welded Tubes for Irrigation Purposes.
All manufacturers, whether Indian or foreign, must hold a valid BIS licence before selling this product in India. Operating without ISI Mark certification is a punishable offence under Indian law.
BIS Certification Procedure of Aluminium Alloy Welded Tubes for Irrigation
The process can be undertaken and certified for the Indian manufacturer and for the foreign manufacturers:
BIS Certification India for Indian Manufacturers (Standard Timeframe – 30 days)
BIS FMCS Certification for Foreign Manufacturers (Standard Timeframe – 180 days)
Requirements to Obtain BIS Licence for IS 7092 Part 1
To qualify for BIS certification, manufacturers must meet the following prerequisites:
- Raw materials conforming to IS 7092 Part 1 and IS 737 alloy specifications
- In-house testing laboratory equipped for mandatory tests
- Competent Quality Control Personnel
- Full adherence to BIS guidelines under IS 7092 Part 1
Documents required fall under four categories:
- Administrative Details
- Technical Details
- Quality Control Personnel Details
- Commercial Details
ISI/BIS Certification Cost Details
Expenses involved in obtaining BIS Certificate for Aluminium Alloy Welded Tubes for Irrigation Purposes as per IS 7092 Part 1 under the Product Certification (Scheme-I) of BIS :
|
S No. |
Particular |
Amount (INR) |
Remarks |
|
1. |
Application Fee |
1000 |
To be paid directly to BIS |
|
2. |
Audit Fee |
7000 |
To be paid directly to BIS |
|
3. |
License Fee |
1000 |
To be paid directly to BIS |
|
4. |
Sample Testing Fee |
As Applicable |
To be paid directly to BIS (Testing charges vary from product to product and lab to lab.) |
|
5. |
Minimum Advance Marking Fee |
As per actual |
To be paid directly to BIS (Marking fee varies as per Indian Standard) |
|
6. |
Renewal Fee |
1000 |
To be paid directly to BIS |
|
7. |
Inclusion Fee |
5000 |
To be paid directly to BIS |
|
8. |
ERCS Pvt Ltd Service Fee |
Please contact info@elitasrcs.com |
|
|
Remarks |
Including all the taxes |
||
- In the certification process, product testing is the most important stage as it determines whether the quality of the product meets Indian standards.
- For the same purpose, investments in testing facilities are required to install test equipment for internal factory test laboratories.
- Apart from the charges mentioned above in the table, we may ask you to pay/reimbursement for a Pre-Visit at your Factory Premises to ensure the conformity of your product as per the relevant Indian Standard & BIS guidelines for its BIS certification.
Role of ERCS Private Limited in getting your product certified :
- To get BIS certification and produce a standard quality product, the manufacturer must ensure that their product follows the specified Indian Standard Specifications (ISS), which we directly interpret to you from the BIS officials as per the Indian Standards.
- ERCS Private Limited will be your friend, philosopher and guide in the whole process of getting your product certified by the concerned authorities/ departments.
Scope of work by ECRS Private Limited:
a. Ensuring the conformity of your product as per IS 7092 Part 1:
ERCS Pvt. Ltd. has developed a vast network within the Aluminium & Aluminium Alloy Industry, various BIS departments to assist for ensuring conformity of the product Aluminum Alloy Welded Tubes for Irrigation Purposes according to IS 7092 Part 1.
b. Effective documentation with awareness of the BIS guidelines:
In order to facilitate the manufacturing industry in obtaining BIS certifications, guidelines have been developed. Our team has the experience of completing over 150 projects and technically competent associates in various Industries.
We are familiar with the Indian Standard Specifications & BIS guidelines and deliver the most suitable interpretation to the Quality Control Personnel so we can do a reliable and effective documentation of your product in accordance with the BIS guidelines.
c. A pre-visit can be paid at your factory premises:
In the process of getting BIS certification, the officer from the BIS authority visits the factory for inspection. In order to get good results, the BIS inspection should go smoothly without any Non-Conformity. By keeping this goal in mind, our team will organize a pre-visit to your factory premises so that the required changes can be made to remove the elements of fallibility.
d. Assistance for BIS audits:
We will explain the whole procedure of conducting a BIS inspection and make you aware of the things that need to be prepared and readily available at the time of inspection.
Benefits of getting ISI Mark for Aluminium Alloy Welded Tubes for Irrigation Purposes
- The term “ISI mark" means that a certain product conforms to the quality standards set by the government.
- It is compulsory for Aluminum Alloy Welded Tubes for Irrigation Purposes to obtain the ISI Mark, and the violators are penalized with the seizure of the material seize and a significant sum as a fine.
- Getting certification improves the probability of your product surviving and competing in the market.
- Customers tend to buy ISI-certified products as it ensured safety and standard quality. Hence, with the certified products, you can win the confidence and trust of the buyer.
- With the word of mouth of such a client list, you can establish your credibility in the market.
- Hence, with the renowned brand, you can raise the standard and benchmark the market value of the product